031 Samurai
Coming soonEPA registration pending · coming soon.
FROM THE RIGHT COATING TO THE RIGHT QUANTITY
Find what you need, then work out how much.
Already know your product? Go straight to the calculator.
Choose the application state to see the options for your project. Pending products are marked coming soon. Leave the application state undecided for a planning estimate. Selecting California uses its product range.
Choose states to see products available for your project, or leave locations undecided for a planning estimate.
WHAT YOU NEED
YOUR COATING OPTIONS
A quantity estimate does not clear any technical review points shown below.
EPA registration pending · coming soon.
HOW MUCH YOU NEED
Choose U.S. or Canada. Under U.S., select the application state; California automatically uses its product range and guidance.
036: 70 kn. 038: average operating speed up to 35 kn; occasional faster trips are acceptable with an additional coat recommended. Never recommended above 35 kn average; not recommended for freshwater-only use; mixed-water cruising, including superyachts, cruisers and trawlers, remains eligible with a freshwater-exposure warning. Freshwater-only lake use excludes 038 regardless of boat size. 041: 40+ kn, recommended for sportfishing and performance / smooth finish, including speeds above 40 kn; suitable for freshwater use. 021: available in Canada only; same average-speed and existing-antifouling compatibility rules as 038. Seasonal salt/brackish protection only. Multi-season plans may consider it with seasonal inspection and recoating; one application does not provide multi-season protection. Check the supplied specification where older sources differ. Fuel savings is a selection priority, without a promised percentage. 041 is the preferred conventional option for most non-aluminum boats and fuel-savings requests. 038 is favored for eligible aluminum/copper-free profiles and suitable sailing yachts, catamarans, superyachts, cruisers or trawlers at average speeds up to 35 kn when the preparation preference permits it. Direct-compatible preparation takes priority; 015 tie-coat and removal alternatives remain visible. At 50+ kn average, prefer 036 and RX PRO; 041 remains an alternative with an additional coat. 036 retains its 70 kn maximum-speed limit. Performance / smooth finish and sportfishing favor 041 below the 50+ kn average range. Standard RX remains a high-speed alternative where otherwise suitable; sportfishing uses RX PRO. Clear is the best future fit for mostly stationary boats; RX PRO is the available recommendation until Clear is released. SEOSIL has no speed limit and is suitable for salt, brackish, fresh and mixed waters and all hull materials with the correct preparation.
Hull area uses the existing product coverage rates, with 10% material allowance for brush / roller or 30% for eligible spray applications, then rounds once per product. Required full-area primer coats are included automatically without repair-percentage questions. Local-repair preparation routes use the percentages entered; standalone manual estimates retain their separate scopes. Repair percentages apply to the full hull area before rounding. Planned spray coats do not reduce the required total film build. 038 spray estimates require review: the older U.S. TDS prohibits spraying while the 2026 EPA commercial-use/heavy-duty marine label includes airless spraying. Confirm the supplied label and applicable use with Seajet; a quantity estimate does not confirm application permission. Published length charts are separate estimates. Catamarans use measured combined underwater area or a separate calculated length guide for cruising catamarans; both hulls are counted once. The guide is approximate, with manufacturer-reference checks from 38–52 ft and extrapolated rows outside that range. Measured area remains preferred. SEOSIL uses total film build, not an extra coat multiplier.
Pellerclean uses the existing equipment guide or measured-area engine. Package estimates prefer fewer packages, then less unused allowance. Canada and California full-system kits start at Medium. Clear-only results recommend separate 375 ml / 750 ml packs from one 4 mil WFT coat; plastic and rubber use Clear without primer.
SEOSIL Primer + RX is the base system. RX PRO is optional over RX. Clear is marked coming soon and is a planning-only calculator entry. Do not combine PRO and Clear. When guided preparation specifies 117 or 015, its required quantity is included with the selected coating. Percentages are requested only for local-repair primer routes. A required full coat of 015 is included directly; standalone manual primer calculations remain available.
Bare hull material and existing epoxy barrier are separate paths. Bare aluminum uses one standard 117 coat at 3 mil DFT. Two roller coats are recommended on bare GRP and steel. For full osmosis protection on GRP, 9 mil total dry-film thickness (228.6 µm) is required. Apply additional coats as needed to achieve the required thickness. An intact, compatible epoxy barrier uses at least one fresh 117 coat (4 mil DFT on GRP / gelcoat; otherwise 3 mil DFT). Wood uses the preparation specified for the chosen coating system; no unverified 015 dilution is assumed. SEOSIL uses its own substrate preparation, including its specified wood mist coat.
For existing silicone, identify the system: Clear / Bioclean Eco receives a fresh-water wash and another Clear coat; RX may receive RX, RX PRO or Clear; RX PRO receives RX PRO only. Other Seajet silicone systems require Seajet USA office guidance. Other or unknown silicone coatings require removal. Conversion from conventional bottom paint to a new silicone system requires removal to bare hull or compatible epoxy. Preparation, additional stripe coats, repairs and a dedicated barrier specification need confirmation.
Existing-paint preparation uses all 30 rows of the current U.S. guide compatibility chart, pages 20–21: A = wash, remove loose paint and spot prime; B = A plus light sanding; C = A plus one full coat of 015; D = remove existing antifouling. 041 follows 036. For all compatible overcoating routes (A–C), current Seajet guidance recommends light sanding and removal of loose paint. Use 015 Underwater Primer for spot priming over existing antifouling. Use 117 Multipurpose Epoxy Primer only on exposed hull material, existing epoxy barrier coats or fillers; carefully mask repair areas so 117 never overlaps existing antifouling. For 021, use the same compatibility routes as 038. 015 is an isolating / tie barrier here, not the 117 epoxy osmosis system.
References: North American selector reviewed 19 October 2026; U.S. Product Guide (16 August 2026); Canada Digital Product Guide (28 August 2026); existing audited hull and Pellerclean calculators (September 2026).